My Favorite Books

Monday, March 7, 2016

Solar Fast Process

Back in 2014, I was a guest blogger on And Then We Set It On Fire.  I've had more than once person ask me about the process on the leaves I posted this past week using Solar Fast.  I'm copying the blog post I did for using Solar Fast.  Hope this explains (or bores you totally!) on how I created my leaves and other prints!   Any questions, just give me a shout!

Monday, June 16, 2014

Sun Printing with SolarFast

Robbie here with my turn at sharing another product/technique for sun printing!  Fortunately, our weather here in Michigan was been sunny enough for me to continue my ‘play time’  in the sun with SolarFast (SF)!  SolarFast is a relatively new sunlight developed dye product byJacquard that I first tried last August.  
For this  post, I’m going to show you how to sunprint using negatives that you've printed from your ink jet printer.  This is one of the advantages of SolarFast…the ability to create photographs on fabric or other natural substrate.  In addition, there is no change to the hand of your fabric, heat setting isn't required, no mixing (dye comes straight out of the bottle!) and you clean up with water!  

First off we need to find a photo to print in black and white!!  Even if your photo is in color, you can change the settings on your printer or in a photo editing program to black/white.  The end result is you need a photo with high contrast, in black and white, which you'll print out on transparency film.  
Last summer, I used the image above to print out on SolarFast Transparency film, which I purchased fromJacquard.   I think any transparency film would work - as long as it's for use in ink jet printers.   

At the time, all I saw in my image was black and white, and for the most part this image worked well enough for my 'first' time printing.   


So let's get started on the process!   And along the way I will add 'tips' in red but you can also go to the Jacquard web site for more tips and tricks.  

The process is simple.....I used a piece of foam board to work on as it's easier to carry the board outside..  You do not want to paint your fabric outside!!!  Remember this product reacts in the sun!!  Work inside!
 I started with white cotton sateen (prewashed & dried) and simply painted a layer of  purple SF using an inexpensive paint brush (you could also use foam brush).  
You want your fabric just wet enough to cover the area you want printed but not soaking wet.  It's recommended you blot with a paper towel. 
** TIP - If the fabric is TOO wet during exposure, condensation may form underneath the negative, which can interfere with development. 
**Tip - I use a hard brayer to roll across my negative  - just helps to adhere to the paint before laying glass on top.  You want your film to be flush on the painted area of your fabric.  
**TIP - Make sure the ink/printed side of your transparency is facing up!  This is two fold...your negative will last for multiple prints and you won't smear ink onto your fabric. Ask me how I know this!

Next step is to lay your negative on  the painted area then lay a piece of glass on top to hold the negative in place.
**Tip - Make sure your glass is not too thin!  It will potentially crack with the heat of the sun!!  
Now carry your piece out into the sun (this is where working on foam board comes in handy).   Exposure time is anywhere from 10 to 30 min.  It's better to overexpose your piece, but you can always 'peek' by lifting the glass, then lift up an edge on the film.  If the color isn't intense enough, just carefully lay the corner and glass back on to your fabric and go have a glass of wine while waiting!  No more peeking now!  

Once you are happy with peeking and seeing your print develop, bring your print inside with the negative and glass still on top!  Keep your fabric out of the sun until you can wash out the undeveloped dye.  You can purchase a SF Wash but I just used Dawn detergent (blue).  Any undeveloped dye that remains on your fabric could continue to develop, thus you would lose your pattern/design if it's in the sun.  
And this was my  result.  As you can see the leaves printed but the veins weren't defined as much as I would have liked.  But I was happy for my first print.  
**Tip:  Make sure you paint your fabric inside!  Remember SF is activated by the sun!!  And bring your printed piece inside before you remove the glass!!!  Otherwise, you  may lose your entire print!  

So, this time around, I took that same negative but I outlined the veins using a permanent marker.   You could  draw a picture on transparency film or alter a 'negative' once it was printed on the film, as I did with the addition of veins.  Also you can use paint to create or add to a negative (you'll see this in a later post in an example I did with stencils).  





The leaves certainly look better with the the black marker, which added the contrast they needed.  









Instead of using white fabric for this new print, I wanted to show how you can use a color background.   This is a hand dyed cotton fabric.

I painted black SF within an area that would be covered with the transparency film (which is 8 1/2 x 11"),the leaf negative was placed on top of the painted area then a piece of glass was placed on top and then outside for 15 min.  The time for developing your print is dependent on the time of day, intensity of the sun, etc.  


I think this print turned out so much better with the addition of the veins.  



Well, I couldn't stop with just one negative so I looked on the Internet for more black and white photo's.





This picture, in black and white, seemed like a perfect candidate.  I found it on the site here.  

I also adjusted some of the contrast but since I'm not a photo expert, I will leave that part of editing photos for you to research on your own!  Just remember you need high contrast!


White cotton sateen, painted and ready for the negative and glass.




I used Sepia SF for this finished print, which, I think, is a great color.  









I really liked the clock negative so for my last piece I masked off an area the 'negative' would fit into, then painted black SF within that area.

I kept the masking tape on through the entire sun printing process.


This print turned out quite nice and the edges are crisp with the masking.  It does appear blue more than black but I think this is due to exposure time.
I  read on the Jacquard website that black and blue SF will become bluer or blacker after washing.  Also black will require longer exposure time.  


So I hope you found this type of sun printing interesting enough to come back tomorrow for some other ways of using SolarFast and the sun!

3 comments:

  1. Excellent tutorial Robbie……now that you broke down the steps…..it’s far more doable in my mind than it was before….

    ReplyDelete
  2. I loved reading about this and you have made me want to try it. I bet it would become addictive!!

    ReplyDelete
  3. Love your tutorial, which I visited again after seeing your comment on my recent Fire blog post. I need to try your method and will duly credit you with the instruction, if you will allow me to include it in my April posts.

    ReplyDelete

Had to put Word Verification back in! Getting strange messages!!!